Eight Real Storage Advantages Of Our Patented Three-Way Pull-Out System
Nov 19, 2026
Leave a message
What it does, what it doesn't, and where it earns its price
Most drawer hardware is sold as a sentence: *full extension. Soft close. Heavy duty.* After twelve years of specifying cabinet hardware into kitchens in Singapore, Dubai and northern Europe, I've stopped trusting sentences. A mechanism only proves itself once it's in a real cabinet, in a real corner, with a real load sitting in it for three years.
Our patented three-way pull-out is the system we keep coming back to, but not for the reasons on the banner. Here are the eight things it genuinely changes, explained the way I'd walk a dealer through it in the showroom, not the way I'd write a headline.
1. Three ways in, not one
A standard full-extension drawer only gives you one way in: straight at it. In a blind corner, that means climbing half into the cabinet to reach the back row, and pulling everything forward to get at one jar.
Ours opens forward and to either side. In a corner run, at an island end, or in any cabinet with a walkway beside it, you reach the back row from the side instead of through the front. The gain isn't theoretical: it's the difference between unloading four items to get the fifth.
2. The volume doesn't change. What you can reach does.
This is the claim I'd argue hardest against, so let me put it plainly: a three-way mechanism adds compartments, not litres. The cabinet box is the same size it was. What changes is how much of that box you actually use.
In a conventional 600 mm base, most households live in the front 60 percent and let the back 40 percent become a graveyard of duplicate spatulas. With side access, we routinely see that rear zone come back into service. Measure it on your own cabinet before you quote a number. Ours reads around 85 percent usable versus 60-odd. Your millwork tolerances will move that figure.
3. Zoning becomes real, not just tidy
Once a drawer opens in more than one direction, you can assign a direction to a function. Oils and spices on the side you reach while the pan is already on the heat. Prep tools on the side your free hand goes to. Cutlery forward.
That's not a storage gimmick, it's a cooking workflow. In a one-cook kitchen, the difference of half a step per reach, two hundred times a day, is the whole reason people describe a kitchen as "comfortable" without being able to say why.
4. Load rating is directional. So is our spec sheet.
Here is what separates a real product from a rendering. A three-way carriage doesn't carry load the same way in every direction, because the moment arm changes. When a drawer is pulled sideways, the load sits further off the track centreline, and the pull force on the locking pin is nothing like it is in forward draw.
So we publish two figures, not one: rated load forward, and rated load on side pull. Any supplier who gives you a single "heavy duty" number for a multi-directional system is either guessing or hiding it. Ask for both, in writing, and ask what happens at the derated figure on a 500 mm cabinet, which is the worst case, not the best.
5. The clearance trade-off - and when to walk away
I'll correct something most brochures won't: side access needs side clearance. If the cabinet is flanked by walls, a tall fridge panel, or a run of units on both sides, the side pull is physically blocked. There is no mechanism that makes space where there is no space.
What the design does is remove the need for *rear* clearance and let the unit work in tighter boxes than a conventional pull-out, but you must have a walkway or an open end on at least one side.
Our honest rule of thumb: specify it in island ends, corner cabinets with a walkway, open-shelf pantry runs, bathroom and laundry units where the side is exposed. Don't specify it in a fully enclosed wall-to-wall run and then wonder why the side pull never gets used. That's not a product failure, it's a layout decision made too late.
6. Cycle numbers, not adjectives
"Smooth and silent" costs nothing to write. What we can actually show is 50,000 open-close cycles on a loaded carriage, measured at the handle, with the damper still returning inside tolerance and no audible rattle above the ambient kitchen level.
And because I'd rather you heard it from us: our first side-pull locking pin developed a knock at around 30,000 cycles in the 2021 trial batch. We changed the pin material and added a nylon sleeve. The current version is the one that passes. If a supplier tells you their mechanism has never had a failure mode, they haven't tested it long enough to find one.
7. Configurability is a factory question, not a design question
Any brand can say "customisable." What that actually means is tooling, panel optimisation and lead time, and buyers deserve to know which of the three they're paying for.
In practice we work to a fixed set of widths on a 32 mm system pitch, adjust depth to the cabinet box, and offer two carriage depths. That covers most residential and light commercial layouts without turning into a bespoke order. When a project genuinely needs a one-off, we quote it as a one-off, with the tooling cost on the line. Nobody is surprised at the invoice that way.
8. It has to disappear into the cabinet
A mechanism this visible can ruin a good kitchen. The locking hardware sits on the outer face of the drawer box, so the detail that matters is not the track, it's the reveal.
We keep the carriage 2 mm inside the box line so the side gap reads the same as a standard drawer, match the cover cap to the cabinet interior finish rather than shipping a generic grey, and set handle position so it stays centred when the drawer is pulled from any of the three directions. Small things. They're the difference between hardware that looks specified and hardware that looks added.

Where it actually earns its price
If you're deciding whether to put this in a project, here's the short version I give clients:
Specify it when** the cabinet has an exposed side, a walkway, or a blind corner you've been quietly writing off as dead space. The payback comes from recovering that rear zone and from the workflow gain in a one-cook kitchen.
Skip it when the run is walled on both sides, or when the cabinet is shallow enough that a standard full-extension already reaches everything. You'd be paying for a direction nothing can use.
Always ask for directional load ratings, cycle test data with the failure mode named, and a clearance drawing at the actual cabinet width. Any one of those missing tells you more than the brochure does.
A note on the "patent"
Patents are worth stating, not leaning on. Ours covers the carriage geometry that lets one runner set serve three directions without a second track. That's the engineering claim. The commercial claim is simpler: it lets a corner cabinet stop being storage you own and start being storage you use.
If you want to see it under load, we'll send a test carriage with a 40 kg dead weight and the cycle log, and you can pull it apart in your own workshop. That tends to settle the conversation faster than a page of adjectives.


